METERS & CONTROLS
PRESSCONTROL
Presscontrol and Mascontrol controllers are electronic pressure
switches with integral dry running protection and non-return valve.
They will start a pump immediately when a valve in the pipe system
MASCONTROL
is opened and stop the pump immediately when the valve is closed,
or if the pump runs dry. They can be fi tted directly to any surface
BRIO
mounted pump, or in the delivery line of any submersible that operates
within the rated pressure and fl ow specifi cations. Suitable for pumps
with 230v motors that do not exceed 1.5kW. The column of water
between the switch and the highest outlet must not exceed 15
■ up to 10 bar ✔ Surface pumps
metres (1.5bar), otherwise the system pressure may not fall to the
■ dry run protection ✔ Submersible pumps
pre-set “cut in” pressure and the system will not restart. They must be
■ electronic control
operated vertically. This control is pre-set at factory, so no additional
■ single phase
programming is required/possible on installation.
The Brio uses the same system and has the same features as the
Presscontrol and Mascontrol controllers, however the initial cut in
pressure can be altered (by removing the cover and turning the
adjuster) between 1.5 and 3.5 bar and it can be operated vertically or
horizontally. It is also has a pressure gauge, which allows the starting
PRESSURE SWITCHES
pressure value and system pressure to be checked. It can be used
in conjunction with shower pumps in installations where there is a
negative head, i.e. the shower head is above the water level in the
cold water tank, and also where the pumps are supplying several
outlets at once e.g. body jets, or domestic water supplies. It also has
a built in timer which will automatically try to reset itself in the event of
a previous shut down due to lack of water. Suitable for pumps with
230v motors that do not exceed 1.5kW and 110v motors that do not
exceed 0.75kW. Reset device not available on 110v.
Presscontrol
Brio
Mascontrol
model in/out volt amps max fl owrate temp min - max pump start
(BSPM) max (l/min) max C° pressure pressure
Presscontrol 1" 230 8 166 65 3 - 10 bar 1.5 bar
Mascontrol 1¼" 230 16 200 65 3 - 10 bar 1.5 bar
Brio 2000M 1" 110 230 12 80 65 2 - 3 bar 1 - 3.5 bar
46 FAX: 01622 355019
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84 |
Page 85 |
Page 86 |
Page 87 |
Page 88 |
Page 89 |
Page 90 |
Page 91 |
Page 92 |
Page 93 |
Page 94 |
Page 95 |
Page 96 |
Page 97 |
Page 98 |
Page 99 |
Page 100 |
Page 101 |
Page 102 |
Page 103 |
Page 104 |
Page 105 |
Page 106 |
Page 107 |
Page 108 |
Page 109 |
Page 110 |
Page 111 |
Page 112 |
Page 113 |
Page 114 |
Page 115 |
Page 116